Expert Answers about Ford F-350, 450, and 550 Cab and Chassis
- Rear Sway Bar that Fits 2000 Winnebago Suncruiser Itasca built on a Ford F-550 Chassis
- We have a rear sway bar that fits your Winnebago Suncruiser Itasca built on a Ford F-550 chassis with the part # RM-1139-143 which comes with all of the components needed to install as well.
view full answer... - Do The Demco Base Plates for a 2001 Ford F-350 Mount In Front of Bumper Brackets
- The Demco Classic Base Plate Kit part # DM9517109 which is a fit for a 2001 Ford F-350 will install in front of the bumper brackets which you can see in the attached photo below.
view full answer... - Finding the Plug for a Brake Controller on a 2013 Jayco Greyhawk Class C
- The plug that your Adapter, like part # 3034-P for the Prodigy P3 # 90195, could be in a few locations around your dash.
Start by looking under your driver side dash. A lot of times it will be near the Emergency Brake or tucked up under the dash. Also check the passenger side for the connector as well as behind your dashboard.
Another place that you can try checking is underneath your driver side seat.
Sometimes it can be a little tricky to locate the plug since it can vary by year/make/model...
view full answer... - How To Wire In The LaSalle Bristol 12V RV Ceiling Fan w/ Wall Switch # 344410TSDC42BNBK
- The four wires in the picture of the 12V RV Ceiling Fan w/ Wall Switch # 344410TSDC42BNBK you referenced are coming from the wall remote # 344410TSSW12V. You'll wire the wall remote in the following manner:
White: Fan Motor +
Blue: Fan Motor -
Black: Trailer Battery -
Red: Trailer Battery +
view full answer... - Which Pins to Use for Charge Wire of # RM-156-25 When Attaching to Trailer Connector
- The center pin of a 6-way is typically the 12 volt accessory circuit which is commonly used for charging batteries. The same 12 volt pin on a 7-way is the one in the 1:00 position.
Between the two connectors styles those are the correct pins to use.
view full answer... - Brake Controller Connector Location on a 2007 Ford F-550
- The brake controller adapter, like part # 3065-P for a Tekonsha brake controller like the P2 # 90885, installs at the connector which is located behind the storage pocket that is built into your center dash right above the ashtray (see attached photos).
I have attached the installation details for this adapter which will apply to matter what brand brake controller you have. Please note that in some cases you may need to run additional wiring # 37185 to complete the brake controller circuit....
view full answer... - Where to Attach Auxillary Power Wire on Vehicle Side 7-Way connector on 2001 Ford F-350
- Yes, you will use the number 4 pin on your 7-way connector, item # PK12703, which may also be labeled Red. The normal attachment is a Black 10 gauge wire to this connection for charging the trailers battery and powering 12 volt accessories.
view full answer... - Can the Bulb Inside the Optronics Backup Light BU45CB Be Replaced
- Correct, the bulb inside the Optronics Backup Light part # BU45CB is not replaceable because this is a submersible light therefore sealed. I would not really call this bad engineering as it was designed this way for a reason. If you were to replace the bulb you would have to break the seal and then the light would no longer be submersible.
view full answer... - Aftermarket Trailer Brake Controller on 2005 Ford F-350
- Installing an aftermarket trailer brake controller like the excellent Tekonsha Prodigy P3 # 90195 with the custom plug-in harness # 3065-P may very well remedy all of the issues that you have been having with the IBC on your 2005 Ford F-350. Generally speaking, integrated brake controllers are known to have some issues and the P3 will absolutely be an improvement. You are correct in your question when you stated that this particular trailer brake controller is considered one of the best...
view full answer... - How To Hook the Hopkins Engager Breakaway Up To The Titan BrakeRite EHB Actuator
- I have attached for you a wiring diagram of the Titan BrakeRite EHB Electric-Hydraulic Actuator for Disc Brakes part # T4813102. If you will be using this with the Hopkins Engager Push-To-Test Trailer Breakaway Kit part # 20099 then you would just simply use the blue wire on the breakaway in place of the brown wire in the photo and red wire on the breakaway in place of the violet wire in the photo. The white wire on the breakaway can then be run to the main trailer ground.
view full answer... - How to Install Replacement Double Ball Joint # LC301695
- It sounds like you might need to set up the linkage # LC388220 properly so that it will allow your steps to function properly. I attached an install instruction sheet that shows how to install it properly. Try that and let me know if you are still having issues.
view full answer... - Trouble Shooting Trailer Brakes That Are Weak or Not Working With a Brake Controller
- The Tekonsha Prodigy P3 # 90195 should be pushing 12 volts when on full power or when using the manual override lever. The trailer brakes should be drawing somewhere between 3.2 to 4 amps. From what it sounds like, you are within these parameters, so odds are you are having a ground issue with the trailer. Especially with the front axle locking when power was applied. What I would do is ground each brake separately and double check any other ground wires. You will want to make sure all...
view full answer... - Where to Locate the Radio Code on a Jensen Radio and How to Use Satellite Radio
- I was able to locate the owners manual for the Jensen VR209TP. According to the manual "Before you listen to Sirius Radio, you must subscribe to the service using your radio's identification number. To display the Radio ID, touch the TUNE + or TUNE - button to access channel “000”. The screen displays "Radio ID" followed by a 12 figure ID number."
One other thing to keep in mind is that even though your Jensen radio is compatible for SiriusXM radio you may not have the appropriate tuner...
view full answer... - What Is The Derale Push-In Radiator Probe, # D16736 And How Is It Installed On A 2010 Ford F-350
- The Derale Replacement Push-In Radiator Probe for Derale Single-Stage Thermostat Fan Control, part # D16736, is a thermostatic probe that is inserted into the vehicles radiator and connects to a thermostat switch. The probe will register the temperature of the fluid in the radiator and allow the switch to turn the fan on if the temperature exceeds 180 degrees, and will turn the fan off when the temperature drops to 165 degrees.
On the Derale Premium, Single-Stage Thermostat Fan Control...
view full answer... - What is Standard Size Rivets for Installing RV Tub Surround
- We only carry the 1 inch long rivets for installing shower surrounds with the part # LC210278 which is the standard size for this application. We do not have a shorter version since this is the standard size.
view full answer... - Does Push Button Switch for Power Vents # DG52451VP Stay On Once Pressed
- Push Button Switch for Power Vents # DG52451VP is a momentary switch. It is meant to be installed so that when the vent lid is closed it holds the button in which cuts off power to the vent fan. When the lid opens the button is released and it will allow power to go to the fan.
Personally I like toggle switches such as # PK34513 because there is just something satisfying about flipping a switch like it.
view full answer... - Troubleshooting Finding Tow Package Connector for Prodigy P2 Installation on 2008 Ford E-450
- That is correct. There are two connectors and you need to make sure you choose the correct one. Instead of looking for a brown connector it may help to look for one that has a blue, red, and green wire running into it. This should be the connector you need for the # 3035-P.
I have attached an installation video for your reference. You can see the connector starting at the 5 minute mark in the video.
view full answer... - Fuse To Tap Pink Wire of Air Lift WirelessAIR Compressor System on 2015 Chevy Silverado 1500
- Airlift recommends using a keyed circuit that's only active when the ignition is turned on, as the system can activate if the vehicle moves (a strong wind could possibly do it) and possibly drain the battery.
According to the installation instructions, the pink wire from the compressor harness shouldn't be installed on a circuit rated for more than 10A in order to prevent damaging the compressor. I looked over an online copy of the owner's manual, trying to find a good place to tap that...
view full answer... - Where is the Brake Controller Adapter Port on a 2007 Gulf Stream Yellowstone
- According to my research, your 2007 Gulf Stream Yellowstone is on a Ford E-450 chassis. If that is the case then the brake controller adapter port, if present, will be located under the driver dash panel near the emergency brake pedal. I have attached a video which shows this location at around the 5:20 mark.
In order to install the Hopkins Agility Trailer Brake Controller part # HM47295 you will want to use the Hopkins Plug-in Simple Brake Wiring Adapter part # HM47715 if the brake controller...
view full answer... - Installation And Torque On Roadmaster Reflex Steering Stabilizer
- For your Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK22-RSSA, you should have received instructions. My apologies if this wasn't the case. I've attached a photo of the torque requirements from the instructions and have also attached the instruction link.
I recommend using the Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube # LT37420 because they will be vibrating and you don't want the bolts to come loose.
view full answer...
Go To Results